In part one of this series we discussed where to buy your boards. In this next session, we’ll talk about how to work out how much you need.

If you go to one of the big sheds or a builders’ merchant you’ll be presented with a limited range of species and sizes of ready-planed boards, so you’ll have to pick the closest size that will fit your project. Buying from a timber merchant will open up more choices, but you will need to take into account that they will be selling sawn boards which will need to be planed to size.

Assuming you don’t have an unlimited stockpile of timber at your disposal and can work your way through it until you’ve completed your project, you’ll want to take a systematic approach to order what you need.

Measure and list out all the parts, noting the Length – Width – Length

At this stage, you probably have a working drawing with these details written on it so it’s a simple matter of taking off those measurements and adding them to a cutting list. Take a look at the sample cutting list below.

ROTATE SCREEN FOR FULL VIEW

ItemNumberLWt
Tabletop – 3 boards wide345015019
Legs44304545
Rails43604519
Cutting List – Coffee Table – Finished Sizes in mm

Your finished sizes (W x t) are the planed dimensions, so now you must convert these dimensions into the sawn size if you are buying stock already sawn into boards. For our example, the board sizes will come out as follows:

Planed Size (W x t)Sawn Size (W x t)
150 x 19175 x 25
45 x 4550 x 50
45 x 1950 x 25
Planed vs Sawn Dimensions

Now let’s total up the sawn dimensions:

NoSawn L x W x t – mmTotal Board Length x (W x t) – mm
3450 x 175 x 251350 x 175 x 25
4430 x 50 x 551690 x 50 x 50
4360 x 50 x 251440 x 50 x 25
Calculating the Board Run

Now that we have the total lengths of the pieces we can see that 1350mm will take a whole 175mm x 55mm board because it’s quite wide.

The remaining pieces are relatively narrow and could be ripped from a single board 1690mm x 80mm x 25mm.

If maths isn’t your thing you’ll be pleased to know that there are online calculators that’ll do the hard work for you.

Wastage Allowance

We haven’t made any allowance for waste or cutting so let’s add on some. 10% is suitable for boards with no defects, but you would be wise to add a bit more to avoid splits, knots and other undesirables. I like to be generous with my waste so that I can have spare material to call upon if I make a mistake along the way. Waney edge timber is likely to need a bigger wastage allowance than square edge stock. Let’s add 20% waste and add it to the lengths of our boards.

1350mm + 20% = 1620mm
1690 + 20% = 2028mm

Armed with these measurements we can head off to the timber merchant, but first, let’s work out what it’s going to cost.

The timber merchant is going to want you to buy a whole board, not just a bit of it. If you need a small amount ask them if they have an off-cuts pile you can rummage through. Otherwise, be prepared to buy a board that is closest in size to your needs. Lengths and dimensions tend to vary so check with your timber merchant to see what they stock.

Let’s say our timber merchant stocks 200mm wide boards with lengths of 2400mm and 3000mm. 2400mm is plenty for our needs as we’ve already added waste so it makes sense to go with the shorter of the two options. We will end up ordering the following:

1 board @2400mm x 200mm x 25mm

1 board @2400mm x 200mm x 50mm

Calculating The Cost

Timber merchants do not charge by the length but by the cubic metre/foot. So to work out how much you’re going to pay before you order you’ll need to convert your lengths into volume. To do this we need to multiply the L x W x t.

1 board @2400mm x 200mm x 25mm = 12,000,000 cubic mm
1 board @2400mm x 200mm x 50mm = 24,000,000 cubic mm


Now let’s convert those scary numbers into cubic meters.


12,000,000/100,000,000 = 0.012 cubic meters
24,000,000/1000,000,000 = 0.024 cubic meters

My Timber Merchant Uses Feet and Inches

If your timber merchant is still old school and charges by the cubic foot then multiply the cubic metre figures by 35.315 as follows:

0.012 x 35.315 = 0.424 cubic feet
0.024 x 35.315 = 0.847 cubic feet

Now all we need to do is multiply these figures by the cost per cubic metre or feet.

Let’s go with £35.00 + VAT per cubic foot:

0.424 x 35.00 = £14.84 + 20% VAT = £17.81
0.847 x 35.00 = £29.64 + 20% VAT = £35.57

Total Cost of Timber – £17.81 + £35.57 = £53.38

If we do the same for cubic metres using £1236.00 + VAT per cubic metre we get:

0.012 x 1236.00 = £14.83 + 20% VAT = £17.79
0.024 x 1236.00 = £29.66 + 20% VAT = £35.59

Total Cost of Timber – £17.79 + £29.64 = £53.38

So as you can see, the totals come out the same.

With experience, you can get a sense of how much your order will cost, but in the beginning, the real versus imagined total can come as a shock so it is worthwhile going through this exercise.

We cover buying wood and much more in CORE SKILLS UNDERSTANDING WOOD.

For a comprehensive list of our favourite timber merchants and tool shops, click here.